乘法器第一階段測試通過

`define NUM_STATE_BITS 3
`define IDLE 3'b000
`define COMPUTE 3'b001

//`include "clock.v"

module slow_div_system(pb,ready,x,y,r3,sysclk);
input pb,x,y,sysclk;
output ready,r3;
wire pb;
wire [11:0] x,y;
reg ready;
reg [11:0] r1,r2,r3;
reg [`NUM_STATE_BITS-1:0] present_state;

always
begin
@(posedge sysclk) enter_new_state(`IDLE);
r1 <= @(posedge sysclk) x;
r2 <= @(posedge sysclk) 0;
ready = 1;
if (pb)
begin
while (r1 >= 1 | pb)
begin
@(posedge sysclk) enter_new_state(`COMPUTE);
r1 <= @(posedge sysclk) r1 - 1;
r2 <= @(posedge sysclk) r2 + y;
r3 <= @(posedge sysclk) r2;
end
end
end

task enter_new_state;
input [`NUM_STATE_BITS-1:0] this_state;
begin
present_state = this_state;
#1 ready=0;
end
endtask

always @(posedge sysclk) #20
$display("%d r1=%d r2=%d r3=%d pb=%b ready=%b", $time, r1,r2,r3, pb, ready);
endmodule


module top;
reg pb;
reg [11:0] x,y;
wire [11:0] quotient;
wire ready;
integer s;
wire sysclk;

cl #20000 clock(sysclk);
slow_div_system slow_div_machine(pb,ready,x,y,quotient,sysclk);

initial
begin
pb= 0;
x = 4;
y = 4;
#250;
@(posedge sysclk);
//for (x=0; x<=14; x = x+1)
begin
@(posedge sysclk);
pb = 1;
@(posedge sysclk);
pb = 0;
@(posedge sysclk);
wait(ready);
@(posedge sysclk);
if (x/y === quotient)
$display("ok");
else
$display("error x=%d y=%d x/y=%d quotient=%d",x,y,x/y,quotient);
end
$stop;
end
endmodule

乘法器模擬

`define IDLE 2'b00
`define INIT 2'b01
`define COMPUTE1 2'b10
`define COMPUTE2 2'b11

module cl(clk);
parameter TIME_LIMIT = 110000; //1250;
output clk;
reg clk;

initial
clk = 0;

always
#50 clk = ~clk;

always @(posedge clk)
if ($time > TIME_LIMIT) #70 $stop;

endmodule

module slow_div_system(pb,ready,x,y,r2,sysclk);
input pb,x,y,sysclk;
output ready,r2;
wire pb;
wire [11:0] x,y;
reg ready;
reg [11:0] r1,r2;
reg [`NUM_STATE_BITS-1:0] present_state;

always
begin
@(posedge sysclk) enter_new_state(`IDLE);
r1 <= @(posedge sysclk) x;
ready = 1;
if (pb)
begin
@(posedge sysclk) enter_new_state(`INIT);
r2 <= @(posedge sysclk) 0;
while (r1 > 0)
begin
@(posedge sysclk) enter_new_state(`COMPUTE1);
r1 <= @(posedge sysclk) r1 - 1;
@(posedge sysclk) enter_new_state(`COMPUTE2);
r2 <= @(posedge sysclk) r2 + y;
end
end
end
task enter_new_state;
input [`NUM_STATE_BITS-1:0] this_state;
begin
present_state = this_state;
#1 ready=0;
end
endtask

always @(posedge sysclk) #20
$display("%d r1=%d r2=%d pb=%b ready=%b", $time, r1,r2, pb, ready);
endmodule

module top;
reg pb;
reg [11:0] x,y;
wire [11:0] quotient;
wire ready;
integer s;
wire sysclk;

cl #20000 clock(sysclk);
slow_div_system slow_div_machine(pb,ready,x,y,quotient,sysclk);

initial
begin
pb= 0;
x =2;
y = 3;
#250;
@(posedge sysclk);
for (x=2; x<=2; x=x+1)
begin
@(posedge sysclk);
pb = 1;
@(posedge sysclk);
pb = 0;
@(posedge sysclk);
wait(ready);
@(posedge sysclk);
if (x/y === quotient)
$display("ok");
else
$display("error x=%d y=%d x/y=%d quotient=%d",x,y,x/y,quotient);
end
$stop;
end
endmodule

除法器改成乘法器

結果是對的..但是對於程式細節還不甚了解..繼續研究!!

除法器改乘法器

X設為9Y設為9

除法器

因為之前上課沒有認真聽講

今天想做卻發現不太會

請教同學終於有了解了

以後會更認真上課!!